Linux4Hosts
02-11-2004, 07:14 AM
1-Register Name Servers where you registered your domain at.
I suggest using 1 IP per name server.
NS1.yourdomain.com = IP#1
NS2.yourdomain.com = IP#2
2-Notify your DataCenter to setup Reverse DNS for the IP addresses used above
and for your name servers. (Normally you put in a ticket to request RDNS for "NS1.yourdomain.com = IP#1
NS2.yourdomain.com = IP#2" and they will complete this within a day)
Please note it can take up to 36 hours for your name servers to propogate through the web.
Once they have propogated procede to step #3.
3-Login to WHM
yoursite.com/whm
4-Type:
ns1.yourdomain.com in the Primary Nameserver field.
Press Assign IP Address
Then Press Add an A Entry for this nameserver
5-Type
ns2.yourdomain.com in the Secondary Nameserver field.
Click Assign IP Address
Then Click Add an A Entry for this nameserver
6-Click Manage Nameserver IPs from the left menu in WHM.
If you see any nameservers that do not belong to you, remove them now.
7-Click Initial NameServer Setup from the left menu in WHM
Run this for the "initial name server setup"
8-Login to SSH to restart bind. (Be sure it restarts, so don't do this in WHM)
Type: service named stop
Then Type: service named start
9-While in SSH do the following to verify installation has gone well.
Type: pico /etc/wwwacct.conf
Scroll to the bottom and insure that your name servers are listed like this:
NS ns1.yourdomain.com
NS2 ns2.yourdomain.com
10-While still in SSH do the following to verify installation has gone correctly.
Type: pico /etc/resolv.conf
It should look like this:
domain yourdomain.com
search yourdomain.com
#nameserver 127.0.0.1
nameserver ip address #1 here
nameserver ip address #2 here
11-Check one more thing in SSH to make sure Name Server Configuration went GOOD.
Type: pico /etc/nameserverips
It should look like this:
ip address 1=ns1.yourdomain.com
ip address 2=ns2.yourdomain.com
يا ريت اكون افدتكم :)
I suggest using 1 IP per name server.
NS1.yourdomain.com = IP#1
NS2.yourdomain.com = IP#2
2-Notify your DataCenter to setup Reverse DNS for the IP addresses used above
and for your name servers. (Normally you put in a ticket to request RDNS for "NS1.yourdomain.com = IP#1
NS2.yourdomain.com = IP#2" and they will complete this within a day)
Please note it can take up to 36 hours for your name servers to propogate through the web.
Once they have propogated procede to step #3.
3-Login to WHM
yoursite.com/whm
4-Type:
ns1.yourdomain.com in the Primary Nameserver field.
Press Assign IP Address
Then Press Add an A Entry for this nameserver
5-Type
ns2.yourdomain.com in the Secondary Nameserver field.
Click Assign IP Address
Then Click Add an A Entry for this nameserver
6-Click Manage Nameserver IPs from the left menu in WHM.
If you see any nameservers that do not belong to you, remove them now.
7-Click Initial NameServer Setup from the left menu in WHM
Run this for the "initial name server setup"
8-Login to SSH to restart bind. (Be sure it restarts, so don't do this in WHM)
Type: service named stop
Then Type: service named start
9-While in SSH do the following to verify installation has gone well.
Type: pico /etc/wwwacct.conf
Scroll to the bottom and insure that your name servers are listed like this:
NS ns1.yourdomain.com
NS2 ns2.yourdomain.com
10-While still in SSH do the following to verify installation has gone correctly.
Type: pico /etc/resolv.conf
It should look like this:
domain yourdomain.com
search yourdomain.com
#nameserver 127.0.0.1
nameserver ip address #1 here
nameserver ip address #2 here
11-Check one more thing in SSH to make sure Name Server Configuration went GOOD.
Type: pico /etc/nameserverips
It should look like this:
ip address 1=ns1.yourdomain.com
ip address 2=ns2.yourdomain.com
يا ريت اكون افدتكم :)